Skip to Content

GENERAL TERMS OF WARRANTY

Version 1.0 2026 – Supplementary conditions to Terms and Conditions of TPLAY Sagl, attached to offers and order confirmations.

Download the document in PDF format

1. Subject and scope of application

1.1 These General Terms of Warranty (hereinafter "Terms") govern the warranty on playground equipment, surfaces, and urban furniture elements provided by Tplay Sagl (hereinafter "Tplay") to the Customer, with or without installation.

1.2 The Terms are an integral part of every offer, order confirmation, and contract of Tplay. By accepting the offer or order, the Customer declares to have received and accepted them.

1.3 In case of conflict, the following shall prevail in order: specific written agreements of the individual contract; these Terms; any conditions of the manufacturer referred to in point 4. Customer's general conditions apply only if accepted in writing by Tplay.

1.4 Tplay acts as a direct distributor of the manufacturers of the supplied products. The conventional warranty is that granted by the respective manufacturer (point 4) and is transferred to the Customer through Tplay. 

2. Definitions

  • Defect: a material or manufacturing flaw present at the time of delivery, which compromises the functionality, safety, or structural integrity of the product.
  • Structural integrity: the ability of a component to support the expected loads without breaking, permanent deformation, or loss of stability.
  • Delivery: date of the delivery report or, if Tplay carries out the installation, date of the testing/acceptance report of the work.
  • Parts subject to wear: components that, by their nature, wear out with normal use (see point 6.2).
  • Maintenance log: document in which the Customer records inspections, interventions and replacements according to the standard SN EN 1176-7 and the manufacturer's manual.

3. Legal warranty, manufacturer's warranty and commencement

3.1 Legal warranty. Tplay is liable for defects according to the Swiss Code of Obligations (CO): arts. 197 et seq. for supply only and arts. 367 et seq. for supply with installation (contract for work). If the contract refers to the SIA 118 standard, the relevant provisions on verification, notification and limitation apply.

3.2 Conventional manufacturer's warranty. In addition to the legal warranty, the Customer benefits from the manufacturer's warranty according to point 4. This warranty exclusively covers material and manufacturing defects, under the conditions of points 5 and 6.

3.3 Commencement. All terms commence from the date of Delivery (point 2). Warranty interventions do not extend or renew the original term; replaced parts are guaranteed for the remaining period of the product on which they are installed.

3.4 Proof of warranty. The warranty is valid upon presentation of: invoice or order confirmation, certificate of conformity SN EN 1176 / EN 16630, delivery or testing report and updated maintenance log.

4. Manufacturer's warranty

4.1 For each product, the duration and conditions of the conventional warranty granted by the respective manufacturer (producer) apply, as stated in the warranty certificate, in the technical data sheet or in the manual provided with the supply (hereinafter "Manufacturer Documentation").

4.2 The duration of the manufacturer's warranty may vary based on the material and function of the component, such as load-bearing structures, movable elements, panels, wood, and surface treatments. The applicable durations are those indicated in the Manufacturer Documentation for each product.

4.3 Tplay manages the manufacturer's warranty on behalf of the Customer according to the procedure in point 7. The Customer directs any request to Tplay and not directly to the manufacturer.

4.4 If the Manufacturer Documentation does not specify a duration for a component, the legal warranty in point 3.1 applies.

4.5 The validity conditions and exclusions provided by the manufacturer are in addition to those in points 5 and 6. In case of divergence regarding the duration or extent of coverage, the Manufacturer Documentation prevails.

5. Conditions of validity of the warranty

The warranty is valid only if the Customer complies with all the following conditions. Failure to comply with even one condition voids the warranty for the affected component.

5.1 Compliant installation. Assembly, anchoring, and foundations carried out by Tplay or by a qualified installer, according to the manufacturer's instructions and the standards SN EN 1176-1/-7 and SN EN 1177 (fall zones and impact-absorbing surfaces).

5.2 Periodic inspections according to SN EN 1176-7 and the manufacturer's manual (operational details in point 10):

Type of inspection
Frequency
Who carries it out
Ordinary visual inspection
Weekly (daily for very busy areas or subject to vandalism)
Manager's staff
Functional inspection
Every 1–3 months
Trained manager's staff
Main annual inspection
Every 12 months
Competent inspector

5.3 Maintenance. Tightening of bolts, replacement of worn parts, cleaning and restoration of surfaces according to the manual. Spare parts must be original or approved by Tplay.

5.4 Maintenance log completed, dated and signed for each inspection and intervention, to be presented at Tplay's request.

5.5 No unauthorised modifications in writing from Tplay: additions, removals, welds, drilling, painting or changes of use.

5.6 Use in accordance with the age group, the maximum number of users and the indications on the product label.

5.7 Out of service. In the presence of a defect that compromises safety, the Customer must immediately prohibit the use of the equipment. Damages resulting from continued use after the discovery of the defect are not covered.

6. Exclusions and parts subject to wear

6.1 Exclusions. The warranty does not cover damages or defects caused by:

  1. Vandalism, theft, fire, vehicle impacts or other accidental events.
  2. Improper use or non-compliance with point 5.6 (e.g. adults on preschool play equipment, exceeding the number of users).
  3. Installation, anchoring or foundations not in accordance with point 5.1, if not carried out by Tplay.
  4. Missing, insufficient or undocumented inspections or maintenance in the log (points 5.2–5.4).
  5. Unauthorised modifications, repairs or replacements by Tplay (points 5.3 and 5.5).
  6. Extraordinary natural events: hail, storms, floods, landslides, lightning, snow loads exceeding design values.
  7. Aggressive chemical or environmental agents: antifreeze salt, unsuitable cleaning products, marine or industrial environments not declared at the time of order.
  8. Ground movements or subsidence, water stagnation and foundations not carried out by Tplay.
6.2 Parts subject to wear, excluded from the manufacturer's warranty, unless otherwise indicated by the latter and unless there is a manufacturing defect within 2 years:

  • Ropes (including those with a steel core), nets and chains.
  • Bearings, bushes, joints, hinges and springs.
  • Swing seats, rubber elements and dampers.
  • Sliding surfaces, anti-slip coatings and grips.
  • Bolts, caps and protective covers.
6.3 Aesthetic and natural alterations that do not compromise safety and stability:

  • Scratches, abrasions or chipping of paint and HPL/HDPE panels.
  • Colour variations due to UV rays, including differences between original parts and replacements.
  • Graying of wood, surface cracking, resin formation and dimensional variations due to moisture, typical of natural wood and Robinia.
  • Surface oxidation of screws or non-structural steel parts.

6.4 Indirect damages. Excluded are non-use, loss of operation, monitoring costs, temporary fencing and any other indirect or consequential damage, within the limits permitted by law.

7. Reporting and complaint management procedure

7.1 The Customer must report in writing any defect immediately after discovery and in any case within 10 working days, under penalty of forfeiture (art. 201 CO, art. 370 CO). Visible defects upon delivery must be indicated in the delivery or testing report.

7.2 The report must be sent to Tplay Sagl, Technical Support Office, Via Gen. Guisan 13, 6900 Paradiso, e-mail customer-care@tplay.odoo.com, using the form in Annex A or with the same details. This address automatically opens a case in Tplay's support system (helpdesk): only reports sent to this address are valid for the purposes of the terms of these Conditions.

7.2bis Levels of urgency and channels. Each report indicates the level of urgency; the channel and response times depend on it:

Level

Examples

Immediate action by the Customer

Channel

Tplay response

1 – Immediate danger

Unstable pole, breakage of load-bearing elements, sharp edges, protruding parts, uprooted anchors

Immediately restrict the equipment (tape, fencing, sign "Out of service")

Phone +41 91 210 13 70, then confirm to customer-care@tplay.odoo.com within 24 hours

Within 1 working day

2 – Defect without immediate danger

Through corrosion, cracks in HDPE/HPL panels, deformations, wood rot

Monitor and record in the log; prohibit if the defect worsens

E-mail customer-care@tplay.odoo.com with Attachment A

Within 3 working days

3 – Wear or spare parts

Ropes, seats, bearings, bolts, caps

Schedule the replacement according to point 10

E-mail customer-care@tplay.odoo.com or request for spare parts quotation

Within 5 working days

8.3 Replaced components become the property of Tplay or the manufacturer and must be returned upon request.

8.4 Tplay's overall liability for any claim related to a defect is limited to the invoice value of the defective product. Liability for intent and gross negligence (art. 100 CO) and the mandatory provisions of the Federal Product Liability Act (LRDP) are reserved.

8.5 These Conditions do not limit the rights of the Customer arising from mandatory legal provisions.

8. Warranty services, costs and limits of liability

8.1 For a covered defect, Tplay chooses, at its discretion, between repair and replacement of the defective component. If both are impossible or disproportionate, Tplay grants a price reduction proportional to the component.

8.2 The costs are divided as follows:

Item

Within warranty period

Beyond the manufacturer's warranty period

Spare component

At Tplay's expense

At Tplay's expense

Transport of the spare part

At Tplay's expense

Monitor and record in the log; prohibit if the defect worsens

Labour for disassembly and assembly

At Tplay's expense, if the installation was carried out by Tplay

At the Customer's expense

Transfer, work equipment, surface restoration

At Tplay's expense, if the installation was carried out by Tplay

At the Customer's expense

8.3 Replaced components become the property of Tplay or the manufacturer and must be returned upon request.

8.4 Tplay's overall liability for any claim related to a defect is limited to the invoice value of the defective product. Liability for intent and gross negligence (art. 100 CO) and the mandatory provisions of the Federal Product Liability Act (LRDP) are reserved.

8.5 These Conditions do not limit the rights of the Customer arising from mandatory legal provisions.

9. Applicable law, jurisdiction and final provisions

9.1 These Conditions are governed by Swiss law, excluding the Vienna Convention on the International Sale of Goods (CISG).

9.2 The exclusive competent jurisdiction is Lugano, reserving Tplay's right to act at the Customer's domicile and reserving mandatory legal jurisdictions.

9.3 If a clause is found to be invalid, the others remain valid; the invalid clause is replaced by the valid one that is closest to the original purpose.

9.4 The version of the Conditions in force at the date of order confirmation applies. Tplay may update them for future contracts; the current version is indicated in the header of this document.

9.5 The Italian text is authoritative. Any translations are for informational purposes.

10. Maintenance procedures

Maintenance is the responsibility of the Customer as the area manager and must be carried out according to SN EN 1176-7, SN EN 1177, the manufacturer's manual and the recommendations of the UPI. This point describes the minimum required to keep the warranty valid (point 5).

10.1 Organisation. The Customer appoints a maintenance manager for each area, keeps the documents from point 3.4 and the manufacturer's manual in a single file, and keeps the register updated (Annex B).

10.2 Frequency checks – playgrounds

Frequency

What to check

Typical interventions

Weekly (ordinary visual inspection)

Hazardous items (glass, syringes, waste), obvious vandalism damage, missing or broken parts, level and cleanliness of the impact-absorbing surface, clear free spaces

Cleaning, removal of foreign objects, levelling sand/gravel/chips, prohibition if necessary

Every 1–3 months (functional)

Stability of structures and posts, tightening of bolts, wear of ropes, chains, seats, bearings and joints, abnormal play of moving parts, integrity of caps and covers

Tightening, lubrication of joints where required, replacement of caps and small parts

Every 12 months (main annual)

Overall safety: foundations and anchors (including with sample excavation), corrosion, wood rot at the base of posts, welds, fall zones and height of the impact surface according to SN EN 1177, compliance with SN EN 1176

Written report from a competent inspector with a list of non-conformities and priorities

After extraordinary events

Hail, storms, floods, serious vandalism

Immediate functional inspection before reopening the area

10.3 Frequency checks – urban furniture (benches, tables, bins, bike racks, planters, fences)

Frequency

What to check

Typical interventions

Monthly

Stability and anchors, broken or chipped slats, loose screws, sharp edges, integrity of containers

Tightening, replacement of slats, cleaning

Every 12 months

Corrosion of metal parts, condition of paintwork, wood degradation, foundations

Touch-ups of paintwork, wood treatment, replacements


10.4 Interventions for material

​- Galvanised or painted steel: touch up scratches and chips exposing the metal within 30 days, using products indicated by the ​ ​ ​manufacturer.
​- Stainless steel: clean with water and neutral detergent; do not use carbon steel wool or chlorine-based products.
​Wood and Robinia: keep the base of the posts free from soil and standing water; sand down splinters; treat with suitable products if specified in the manual. ​if specified in the manual.
​- HDPE and HPL: clean with water and neutral detergent; remove graffiti with compatible products; do not use aggressive solvents.
​- Loose impact-absorbing surfaces: regularly restore the minimum thickness and renew contaminated material.
- ​Rubber impact-absorbing surfaces: check for detachment, cracks, and joints; repair open points immediately to avoid tripping.

10.5 Spare parts and personnel. Replacements are only carried out with original or Tplay-approved spare parts (point 5.3). Interventions on anchors, foundations, load-bearing parts, or movable elements should be entrusted to Tplay or qualified personnel.

10.6 Tplay maintenance service. Upon request, Tplay offers a contract for periodic inspection and maintenance that includes the annual main inspection and record keeping.

Appendix A – Defect reporting form


Field

To be filled in by the Customer

Customer / Organisation


Contact person, phone, email


Invoice number / Tplay order confirmation


Delivery or testing date


Product (item code, description)


Serial number / identification plate


Component concerned


Date of defect discovery


Description of the defect


Equipment taken out of service? (yes/no, date)


Date of the last main annual inspection




Mandatory attachments:

Photo of the defect (detail and overview)
Photo of the identification plate
Copy of the maintenance log for the last 12 months
Copy of the invoice or order confirmation


Place and date: ______________________ Signature and stamp: ______________________

Attachment B – Type sheet of the maintenance log



Type of inspection (weekly / functional / annual / extraordinary)

Equipment or item (code, serial number)

Outcome and anomalies found

Intervention carried out or requested

Level of urgency (1–3)

Reported to Tplay (date, case number)

Name and signature

































































Keep the log for the duration of the longest applicable warranty (point 4) and attach the reports of the main annual inspections.


Tplay Sagl  ·  Via Gen. Guisan, 13  ·  6900 Paradiso - Switzerland

info@tplay.ch  ·  +41 91 210 13 70